Roof

Safety

Essential Plus

Premier

Inspect and rate the overall roof condition

√

√

Identify the roof material type and sealants

√

Evaluate the condition of sealant and joints

√

√

Rate the condition of the components on roof

√

√

Identify potential water intrusion points

√

√

Sidewall and End Caps

Inspect and evaluate the appearance and functional condition of the end caps, sidewalls, entrance doors, windows and cargo access doors

√

√

Inspect & evaluate any damage, discoloration and delamination of the side wall and end cap components

√

√

Inspect and identify the material type of the front and rear caps

√

Evaluate the aging and general overall condition of the front and rear caps

√

Slideout Rooms

Identify slideout room drive systems

√

Identify roof material for the slideout room

√

Inspect and rate the roof condition

√

√

Inspect & evaluate condition of seals, sweeps & gaskets

√

√

Evaluate the attached wiring and utility harness under slideout

√

√

Awnings and Slideout Toppers

Safety

Essential Plus

Priemer

Inspect & identify type (manual vs. electric) of awnings, slideout toppers and window awnings

√

Operate & rate condition of awning frames & latching

√

√

Evaluate & rate condition of fabric material

√

√

Measure & document the fabric size of the awnings

√

√

Chassis Turn Signal and Running Lights (12 volt DC)

Inspect the condition of the 7pin connector receptacle

√

Activate and evaluate the operation of the DOT lights

√

√

Visually inspect the chassis battery compartment, the electrical connections and   batteries

√

√

120 Volt AC Electric System (house power)

Inspect & rate condition of power cord & connection ends

√

√

√

Identify any damage or repair of the power cord

√

√

√

Inspect 120volt circuit breaker box

√

√

√

Inspect condition of wiring, circuit breakers & connections

√

√

√

List any heat discoloration to the wiring and connections

√

Verify the separation of all the wiring types

√

Test & verify the output operation of converter for charging of the deep cycle batteries

√

√

Generator – Engine

Safety

Essential Plus

Premier

Generator- Engine – if installed *strongly recommend performing oil analysis to determine internal combustion engine component condition.

Identify model, serial number and run hours of the generator

√

√

Check oil level

√

√

√

Start and operate the on-board generator

√

√

√

Test the voltage output and frequency (60 cycles)

√

Put generator under a load to verify operation

√

Generator – Radiator

Generator – Radiator – if installed on this model of Generator *strongly recommend performing coolant analysis to determine the condition of the coolant fluid and the internal cooling system.

Location of the radiator and cooling fans

√

Visually inspect the coolant reservoir, radiator and hoses

√

√

Inverter – if installed

Identify and note the model and serial number of the inverter

√

√

Visually inspect wiring & connections and fuses/circuit breakers

√

√

Place electrical load on the inverter to verify proper operation

√

Coach Battery System – (12 volt DC Battery Electrical System)

Locate and note the location of the battery stack

√

√

Evaluate condition, age & matched sizing of battery stack 

√

√

Evaluate if positive & negative cables are correctly matched

√

Inspect wiring, fuse panel & fuses of the 12volt DC system

√

√

√

Evaluate operation of  monitor panel  for  tank readings

√

√

Fresh Water System

Safety

Essential Plus

Premier

Verify fresh city water connections are operational

√

√

Test and verify proper filling of the freshwater tank

√

Verify freshwater tank & pressure pump system operate

√

√

Operationally test all freshwater fixtures inside & outside

√

√

Visually inspect the water filtration system (if installed)

√

Wastewater Systems – (Gray and Black Water)

Operationally test and inspect waste (gray and black) plumbing systems for leaks

√

√

Identify the type drain valve controls

√

Verify the operation of drain valves for both systems

√

Operate both drain valves and test for ease of operation

√

√

Verify the drain cap is in place and will hold wastewater

√

√

Life Safety Items

Perform & document LP gas timed leak test at cooktop burner

√

√

√

Test Ground Fault Circuit Interrupter (GFCI) circuits

√

√

√

Test all wall receptacles for correct polarity and ground fault

√

√

√

Test the exterior skin for hot skin for electrical shock

√

√

√

Emergency Exit Windows – Verify all windows are operational

√

√

√

Fire Extinguisher – Verify secure in bracket & is fully charge

√

√

√

Smoke/Fire Detector –Test and verify operation of unit

√

√

√

Carbon Monoxide Detector – Test and verify operation

√

√

√

LP Gas Detector – Verify gas detection and audio alarm

√

√

√

Verify grommet is sealed around LP gas line of water heater

√

√

√

LP Gas System

Safety

Essential Plus

Premier

Visually inspect all hoses and pressure regulators

√

√

√

Verify plastic cover has been installed over the regulator

√

√

√

Perform LP Leak test

√

√

√

DOT Cylinders– if equipped

Document the manufacture date of DOT Cylinder if accessible

√

√

√

List the cylinder sizes that have been installed

√

Conduct visual inspection of exterior of cylinder for rust and other damage

√

√

List the location(s) of the DOT cylinders

√

√

ASME Tank – if equipped

Conduct a visual inspection of tank for rust or damage

√

√

√

List the location of the tank

√

Document the manufacture date of ASME tank if accessible

√

√

List the gallon capacity of the tank

√

√

Refrigerator

Identify the brand, model and type of refrigerator

√

√

Note the location of the vent panels used by refrigerator

√

Operate on all heat sources

√

√

Verify with manufacturer if recall notice issued & completed

√

√

√

Visually verify baffle system on back of refrigerator area

√

Test for interior temperature of upper and lower refrigerator

√

√

Check condition of door frame, shelving, crisper drawers, door shelves and interior light

√

Evaluate & rate the door gasket seals of freezer and refrigerator

√

Water Heater

Safety

Essential Plus

Premier

Identify -the brand, model and type of water heater

√

√

Visually inspect burner assembly and gas exhaust system

√

√

√

Fill tank with water & verify operation on all heat sources

√

√

Operate and verify positioning of bypass valves

√

Determine if proper drain plug installed in water heater tank

√

If installed, inspect and evaluate dauber screen

√

Furnace

If accessible, identify brand, model and type of furnace(s)

√

√

Identify thermostat controls being used to operate furnace(s)

√

Visually inspect air intake and exhaust assemblies

√

√

√

Operate and verify warm air discharge out of vents

√

√

Monitor for unusual noise or vibration of blower motor

√

If installed, inspect and evaluate dauber screen

√

Cooktop / Stove

Evaluate and rate the condition of the cooktop or stove

√

√

List presence and condition of stove top covers

√

Verify ignition & operation of all top burners and oven flame

√

√

√

Inspect & rate condition of metal grill top & rubber grommets

√

√

Evaluate the presence of the control knobs, door handles and oven racks of the unit

√

Air Conditioner(s)

Safety

Essential Plus

Premier

Identify and list the type of cooling unit/heat pump

√

√

Perform cooling efficiency test (Delta T) on each unit

√

√

Visually inspect the plenum box and ductwork sealing

√

Inspect air filter, cooling and heat exhaust coils

√

Washer / Dryer

Visually inspect & verify a wash and rinse cycle

√

√

Visually inspect for leaks or damaged hoses

√

Evaluate and rate exterior condition of dryer exhaust vent

√

Microwave / Convection Oven

Identify brand, model, type and output wattage of the unit

√

√

Verify the rack and turn tables are installed

√

√

Operate unit for 60 seconds utilizing cup of water and  then list water temperature

√

√

Dishwasher – if installed

Identify and list the brand and model of unit

√

√

Verify operation of unit and inspect for leaks and non- functioning racks and wash bars

√

√

Electric Fireplace – if installed

Identify and list the brand and model of unit

√

√

Operate and verify the various heat settings & fan speed levels

√

√

Cooktop Exhaust Fan

Safety

Essential Plus

Premier

Operate & verify condition of exhaust function and fan speeds

√

√

√

Visually inspect the filter and lighting

√

√

√

Evaluate and rate the exterior condition of the exhaust vent

√

√

Ceiling Mounted Fans and Ceiling Exhaust Fans

Visually inspect the condition of the blades and motor

√

Operate & verify condition of blade direction and fan speeds

√

√

Verify lighting if equipped

√

√

Interior Conditions and Appearance

Visually inspect all ceilings, walls, interior doors and flooring for signs of water intrusion & surface damage

√

√

Operate all windows and doors and note any deficiencies

√

√

Evaluate the window coverings

√

√

Operate all interior and décor lighting – 12 volt and 120volt

√

√

Cabinets and Closet Condition

Inspect & evaluate cabinet doors, drawers & pull out operation

√

√

Visually inspect all counter tops and flat surface areas

√

√

Identify & list broken and loose cabinet and closet hardware

√

Note if appearance of previous repairs have been performed

√

Furniture

Safety

Essential Plus

Premier

Visually inspect condition of the dinette table/booth, chairs, recliners and sofa

√

√

Inspect note furniture fabric tears, discoloration and signs of excessive wear

√

√

Visually inspect and note signs of mattress  damage or staining

√

√

Entertainment System

Visually inspect and operate all TV and stereo equipment

√

√

Verify DVD/disc players and radios are operational

√

√

Verify operation of local channels antenna and 12volt DC booster

√

Raise and lower roof mounted antenna if equipped

√

√

Verify remotes are operational

√

Shower / Tub Enclosure

Visually inspect the glass panels, curtains and soap dish areas

√

√

Evaluate & rate seals around framework and doors for leaks

√

√

Operate the door and latch system to verify its operation

√

√

Inspect and evaluate for stains and chemical/mineral build up

√

Leveling System

Identify and note the brand and type of system

√

√

Verify operation by extending and retracting leveling system

√

√

Note visual indications of hydraulic leaks or mechanic issues

√

√

Running Gear (Towable)

Safety

Essential Plus

Premier

Type and number of axles

√

√

Weight ratings for each axle set

√

Inspect the frame, axles, springs, rims and other components   for rust, oil stains and visible damage

√

√

Document the information on the tires

√

√

√

Check tire pressure

√

√

√

Inspect and rate tire tread condition

√

√

√

Note any valve extensions and pressure monitors

√

Hitch System / Hook Up

Inspect and identify the type of system used to tow vehicles

√

√

√

Evaluate and list modifications to hitch system

√

Weight Label and Data Plates

Identify and document vehicle Identification Number (VIN)

√

√

√

Locate and document Vehicle Frame Number

√

√

√

Document the license plate info

√

√

√

List the inspection sticker information – if applicable

√

√

√

List the RVIA inspection seal number

√

√

√

List the Gross Vehicle Weight Rating

√

√

√

List date of manufacture

√

√

√